You might be hearing a weird sound or a leak from the water pump of your Dodge Ram 1500. If you are, you have come to the right place today. Our article is focused on how to change the water pump on Dodge Ram 1500.
Besides how to change water pump on Dodge Ram 1500, we have also included some additional information regarding the topic. Please keep on reading to know more!
What Is A Water Pump?
So a water pump is basically a coolant pump. A water pump is an essential part of your vehicle. This particular object makes sure that the coolant is always moving through the radiator of the car, the hoses of the vehicle, and the engine block of the vehicle. Furthermore, the pump is driven by an auxiliary belt from the crankshaft pulley.
A water pump consists of impeller blades. The impeller blades and centrifugal force produces a force. The effect is used to move the cooled water into the engine of the car. The cooled water might also flow through the water jacket. The water jacket is situated near the combustion chamber.
The hoses take the coolant once the coolant reaches the engine. Moreover, the tubes pass the coolant to the radiator. The radiator is usually situated at the front of your vehicle. The water is now hot again. The hot water flows back to the water pump, and the whole process keeps on repeating.
Dodge Ram 1500 Water Pump and It’s Facts
The ram water pumps might suffer from a water leak. This is a sign that the shaft seal or the gasket has failed. Moreover, the gasket is located between the pump and the engine. Furthermore, failure of the gasket is better than the collapse of the shaft. It is because gasket failure will only need the gasket to be replaced. Shaft failure will need the full pump to be replaced.
The latest water pumps consist of the plastic impeller. Moreover, Plastic impellers are not as durable as the metal impeller. Therefore the plastic impellers might break. The result will be abnormal vibration, which leads to the pump failure.
Now let’s know how to change water pump on Dodge Ram 1500.
Steps Of replace water pump dodge ram 1500
First step
Remove coolant fluid from the cooling system.
Second step
There is a negative terminal of the battery cable. Detach the cable.
Third step
Disassemble the clutch and remove it. Now detach the wiring harness retainer connected to the water pump. This is applicable when you are working with any 3.7 liters and 4.7 liters engine. After doing so, detach the lower hose.
Now take off the fan and keep the clutch of the fan upright. This is to prevent the silicon fluid from leaking. Moreover, do so if you want to reuse it.
Fourth step
Rive the accessory drive belt. Furthermore, remove the radiator hose and the heater hose with the tube. Moreover, do remove the bypass hose and water pump pulley. Do this if you are working with any of the following engines: 3.9 liters, 5.2 liters, 5.9 liters.
Fifth step
Disassemble the engine cooling fan. Now remove the washer bottle and the coolant recovery bottle of the coolant.
After doing so, remove the A/C compressor and the alternator brace. Remove the fan shroud, idler pulleys. Now take off the radiator and the belt tensioner plus the heater hoses. Do so if you are dealing with the 5.7 liters engine.
Sixth step
Finally, take off the pump and fit a brand new water pump, which supports Dodge Ram 1500. After assembling tighten the bolts.
Seventh step
Now connect all the cables back to its place. Do the reverse process of disassembling. After doing so, refill the cooling system. Check if the engine is working as usual. See if all the problems are eliminated. If any issues are seen, then visit a car mechanic.
Conclusion!
We hope your problem was solved regarding how to change the water pump on Dodge Ram 1500. Remember to never attempt to remove the radiator of your Dodge Ram when the engine is hot. This will harm your vehicle. So first, let the truck cool down.
If you liked our article we suggest you visit our recent informative article about How to change a fuel pump on a dodge ram 1500.
Leave a Reply